Water Hose Coiling Product Instructions

This package contains two items:

1. A Hook & Loop ™ Strap to secure the coiled water hose.
2. A Coil-It™ to coil the hose

Step 1.
Unwind Hook & Loop strap off Coil=It™

Step 2: Install Hook & Loop Strap
Make a loop in the Hook & Loop strap by inserting the end of the strap through the buckle. Place this loop over the female end of the hose and tighten. the Hook & Loop strap may be left on the hose permanently.

Step 3: Install Coil-It™
Coil-It™ is a rubber device with two holes, one smaller than the other. Gently stretch the small Cili-It™ hole over the male end of your hose and slide the Coil-It™ down the hose 2 to 3 feet. See Figure 1. Leave the Coil-It™ permanently attached on the hose in this position.

Step 4: Coil Hose
To begin coiling, hold the hose and Coil-It™ in one hand. Place your other hand on the brass male end of your hose and make your first coil by slipping the brass male end through the Coil-It's™ large hole and positioning it on brass end. See Figure 2. Keeping both hands inside the coil, begin coiling by pulling the hose toward you using a smooth hand under hand motion. See Figure 3. Keeping your coils together, continue until you come to the Hook & Loop strap. Now, simply wrap the strap around the coiled hose to complete the task.
To use the hose reverse step 4.

How to use with Quick-Connects or Pressure Regulator?

There are two ways to do this with Coil n' Wrap®. The first one uses the traditional water hose coilit and second uses the 30-Amp coilit.

First the water hose coilit. Put the coilit on the hose without the Quick-Connect or Pressure Regulator being on the hose. Second, make your first coil and put the end of the hose thru the large hole in the coilit. Third add the Quick-Connect or Pressure Regulator to the end. To use the Quick-Connect or Regulator, leave the first loop in and pull the Quick-Connect or Regulator away from the Coil-It® thus making the first loop 3 or 4 inches in diameter. Attach to the rig. When you are finished, disconnect and push the hose back thru the hole in the coilit so you get back to the original size of the coil you had to begin with and then coil the hose. This method works for the majority of our users. Some people however don't want to leave the first small loop in the hose, which brings us to using the 30-Amp coilit .

Using the 30-Amp coilit with a Quick-Connect or Pressure Regulator: The 30-Amp coilit is made from a firmer rubber than used with the water hose. The water hose coilit has to stretch over the end and we can't do that with electrical cords. There is also a slit in the side so you can clip it over the cord on an electrical cord or attach it to a water hose. See picture of the 30-Amp cord coilit. Attach and roll up with the Quick-Connect or Regulator already attached.

I like to join the ends of my hose together. After you have rolled up the hose for the first time with the coilit attached, note where the hose ends are. Move the coilit that is attached to the hose (the one you stretched over the end and slid down about 3') a few inches and roll up the hose again. Moving the coilit changes the size of the first coil and the other coils as you roll it up. This will allow you to set the hose up

I like to leave the hose connected to the rig. Use the 30-Amp coilit at the faucet end. Make your first coil and then walk the hose back to the rig. Good idea to drain it from the rig end first. You will probably find that the hose will bind somewhere along the way back to the rig. Give it a half turn and continue. Put the Hook & Loop tie further down on the hose to secure it.

There are three hose coiling videos. To view a video, left click the title of your choice with your mouse, then click the play arrow. It may take a few seconds for the video to buffer.

3rd Party Video by The Professor of RVing

Order Product